Evaluation of the Taguchi Method for Wear Behaviour of Al/SiC/B4C Composites

➥ ABSTRACT

In this study, the wear behaviors of aluminum matrix composites with an A360 matrix reinforced with silicon carbide (SiC) and boron carbide (B4C) ceramic particles using Taguchi method were investigated. Wear tests of unreinforced aluminum alloy and Al17%SiC and Al17%B4C particles reinforced aluminum composites (Al/17%SiC and Al/17%B4C, respectively) versus AISI316L stainless steel disc were carried out for a dry sliding condition in a so-called a pin-on-disc arrangement. The wear tests were realized at the sliding speeds of 0.5, 1.0, and 1.5 m s−1 and under the loads of 10, 20, and 30 N. The obtained average specific wear rates for Al/17%B4C and Al/17%SiC composites are lower than unreinforced aluminum specific wear rate under the same test conditions. The experimental results are transformed into a signal-to-noise (S/N) ratio of using Taguchi method. Type of the material, applied load, and sliding speed exert a great effect on the specific wear rate, at 48.13%, 31.83%, and 8.77%, respectively. The estimated S/N ratio using the optimal testing parameters for specific wear rate were calculated and a good agreement was observed between the predicted and actual specific wear rate for a confidence level of 99.5%.
Keywords: Aluminum composite, wear behavior, Taguchi method, silicon carbide, boron carbide, pressure infiltration
Cite this article: U.Soy, F.Ficici, A.Demir, “Evaluation of the Taguchi Method for Wear Behaviour of Al/SiC/B4C Composites”, Journal of Composite Materials 46-7, 851-859 pp., 2012, DOI: https://doi.org/10.1177/0021998311410510
[Abstract]  [PDF Download]  [DOI Link]

 

YAYIN VE ATIF BİLGİLERİ

Makale Başlığı Evaluation of the Taguchi Method for Wear Behavior of Al/SiC/B4C Composites
Yazarlar Soy, U., Ficici, F., Demir, A.
Yazar Statüsü Başlıca Yazar
Dergi Adı Journal of Composite Materials
Cilt(Sayı)/Sayfa 46(7), pp. 851-859
Yıl 2012
DOI Numarası 10.1177/0021998311410510
DOI Link https://doi.org/10.1177/0021998311410510
İndeksleme Science Citation Index Expanded
İndeks Linki https://mjl.clarivate.com:/search-results?issn=0021-9983&hide_exact_match_fl=true&utm_source=mjl&utm_medium=share-by-link&utm_campaign=search-results-share-this-journal
Yayınevi SAGE
ISSN / eISSN 0021-9983 / 1530-793X
Atıf Sayısı 20

 

ATIFLAR

No Atıf Yapan Yayının Bilgileri Atıf Yılı Kaynak
1 Vinoth, K.S., Subramanian, R., Dharmalingam, S., Anandavel, B., Optimization of dry sliding wear conditions for AlSi10Mg/SiCp composites using response surface: Genetic algorithm approach, Industrial Lubrication and Tribology 66(5), pp. 593-600, 2014 2014 Scopus,
Web of Science
2 Thirumalai Kumaran, S., Uthayakumar, M., Aravindan, S., Analysis of dry sliding friction and wear behaviour of AA6351–SiC–B4C composites using grey relational analysis, Tribology – Materials, Surfaces and Interfaces 8(4), pp. 187-193, 2014 2014 Scopus
3 Ravikumar, A.R., Amirthagadeswaran, K.S., Senthil, P., Parametric optimization of squeeze cast AC2A-Ni Coated SiC p composite using taguchi technique, Advances in Materials Science and Engineering 2014,160519, 2014 2014 Scopus,
Web of Science
4 Senthilkumar, M., Saravanan, S.D., Shankar, S., Dry sliding wear and friction behavior of aluminum-rice husk ash composite using Taguchi’s technique, Journal of Composite Materials 49(18), pp. 2241-2250, 2015 2015 Scopus,
Web of Science
5 Zhong, L., Wu, T., Guo, S., Li, J., Microstructure and mechanical properties of (Fe, Cr)7C3-Fe/Hadfield steel composites, Journal of Composite Materials 49(20), pp. 2433-2440, 2015 2015 Scopus,
Web of Science
6 Şahin, Y., Ankara, Emre Öksüz, K., Tribological behavior of Al2O3 and B4C particle-reinforced copper matrix investigated by the Taguchi method, Materialpruefung/Materials Testing 58(5), pp. 453-461, 2016 2016 Scopus,
Web of Science
7 Stojanovic, B., Babic, M., Ivanovic, L., Taguchi optimization of tribological properties of Al/SiC/graphite composite, Journal of the Balkan Tribological Association 22(3-II), pp. 2594-2607, 2016 2016 Scopus,
Web of Science
8 Karabulut, Ş., Gökmen, U., Karakoç, H., Kalkan, Ö.K., Çitak, R., Experimental investigation of B4C particulate reinforced aluminium 6061 based composite material in wire-cut EDM, Metallofizika i Noveishie Tekhnologii 37(9), pp. 1239-1251, 2016 2016 Scopus
9 Shanmugavel, R., Sundaresan, T.K., Marimuthu, U., Manickaraj, P., Process Optimization and Wear Behavior of Red Mud Reinforced Aluminum Composites, Advances in Tribology 2016,9082593, 2016 2016 Scopus,
Web of Science
10 Karabulut, Ş., Karakoç, H., Çıtak, R., Influence of B4C particle reinforcement on mechanical and machining properties of Al6061/B4C composites, Composites Part B: Engineering 101, pp. 87-98, 2016 2016 Scopus
11 Veličković, S., Stojanović, B., Babić, M., Bobić, I., Optimization of tribological properties of aluminum hybrid composites using Taguchi design, Journal of Composite Materials 51(17), pp. 2505-2515, 2017 2017 Scopus,
Web of Science
12 Reddy, A.P., Krishna, P.V., Rao, R.N., Dry sliding wear behaviour of ultrasonically-processed AA6061/SiCp nanocomposites, International Journal of Automotive and Mechanical Engineering 14(4), pp. 4747-4768, 2017 Scopus,
Web of Science
13 Areef, S., Ravi Sankar, B., Umamaheswarrao, P., Vinay Krishna, I., Dinesh Kumar, N., Investigations on machining force during end milling of AA6061-sic metal matrix composite, International Journal of Mechanical and Production Engineering Research and Development 8(Special Issue 8), pp. 221-225, 2018 2018 Scopus
14 Karabulut, Ş., Gökmen, U., Çinici, H., Optimization of Machining Conditions for Surface Quality in Milling AA7039-Based Metal Matrix Composites, Arabian Journal for Science and Engineering 43(3), pp. 1071-1082, 2018 2018 Scopus,
Web of Science
15 Bongale, A.M., Kumar, S., Sachit, T.S., Jadhav, P., Wear rate optimization of Al/SiCnp/e-glass fibre hybrid metal matrix composites using Taguchi method and genetic algorithm and development of wear model using artificial neural networks, Materials Research Express 5(3),035005, 2018 2018 Scopus,
Web of Science
16 Liu, W., Yan, H., Zhu, J.-B., Effect of the addition of rare earth element La on the tribological behaviour of AlSi5Cu1Mg alloy, Applied Sciences (Switzerland) 8(2),163, 2018 2018 Scopus,
Web of Science
17 Sagar, K.G., Suresh, P.M., Suresh, R., Wear Behavior of Aluminum Alloy Reinforced with Beryl Metal Matrix Composites Using Taguchi Method, Materials Today: Proceedings 5(11), pp. 24497-24504, 2018 2018 Scopus,
Web of Science
18 Canute, X., Majumder, M.C., Investigation of tribological and mechanical properties of aluminium boron carbide composites using response surface methodology and desirability analysis, Industrial Lubrication and Tribology 70(2), pp. 301-315, 2018 2018 Scopus
19 Choudhary, L., Chhotani, P., Menghani, J., Study on Wear Behaviour on Hardfacing Alloy, Transactions of the Indian Institute of Metals 72(9), pp. 2465-2475, 2019 2019 Scopus,
Web of Science
20 Stalin, B., Ramesh Kumar, P., Ravichandran, M., Siva Kumar, M., Meignanamoorthy, M., Optimization of wear parameters using Taguchi grey relational analysis and ANN-TLBO algorithm for silicon nitride filled AA6063 matrix composites, Materials Research Express 6(10),106590, 2019 2019 Scopus,
Web of Science